The Netgear EAX20 Setup is straightforward. First, plug the extender into a power outlet near your existing router and wait for the Power LED to turn solid green. Use a device to connect to the extender’s default WiFi network. Then, open a web browser and enter mywifiext setup to access the setup wizard. Follow the on-screen instructions to connect the extender to your router’s WiFi network. Once setup is complete, move the EAX20 to your desired location to boost your network coverage.

 

How to Setup Netgear EAX20 using manual guide ?

 

  1. Plug in the Netgear EAX20 extender and wait for the Power LED to turn solid.

  2. Connect your device to the extender's default WiFi network (Netgear_ext).

  3. Open a web browser and go to mywifiext.net setup.

  4. Follow the setup wizard prompts to select your WiFi network and enter the network password.

  5. Choose a location for the extender with a good signal from your router.

  6. Connect your devices to the extended WiFi network.

  7. Test the connection to ensure the extender is working properly.

 

Note: Please contact the technician or visit the official website, www.mywifiext.net setup, if you require any assistance with your Netgear Nighthawk Extender Setup.

 

How to Setup Netgear EAX20 Extender using Wps guide ?

 

  1. Plug in the Netgear EAX20 extender and wait for the Power LED to turn solid.

  2. Press the WPS button on the extender.

  3. Within 2 minutes, press the WPS button on your router.

  4. Wait for the WPS LED on the extender to turn solid, indicating a successful connection.

  5. If the 2.4GHz connection is successful, repeat steps 2–4 for the 5GHz band if supported.

  6. Move the extender to your desired location (within the router’s WiFi range).

  7. Plug in the extender and wait for the Power LED to turn solid.

  8. Confirm that the extender has a good connection to the router by checking the LED indicators.

  9. Connect your devices to the extender’s WiFi network.

 

Netgear EAX20 Wifi Extender setup - Login Steps

 

  1. Plug in the Netgear EAX20 extender and wait for the Power LED to turn solid.

  2. Connect your device to the extender's default WiFi network (Netgear_ext).

  3. Open a web browser and enter mywifiext.net in the address bar.

  4. Log in using the default credentials (admin and password) or your custom login if previously set.

  5. Follow the setup wizard to configure your extender.

  6. Connect the extender to your existing WiFi network by selecting your router’s network and entering the password.

  7. Save the settings, then reconnect your devices to the extended network.

Netgear EAX20 Wifi range Extender setup - Firmware Update 

  1. Plug in the Netgear EAX20 extender and connect it to your device.

  2. Open a web browser and go to mywifiext.net.

  3. Log in using your admin credentials.

  4. Navigate to Settings > Firmware Update.

  5. Click on Check Online to see if a firmware update is available.

  6. If an update is found, click Yes to start the installation.

  7. Wait for the firmware to download and install (do not power off during this process).

  8. Once the extender reboots, confirm the update was successful in the firmware settings.

Netgear EAX20 setup - Reset Process

  1. Locate the Reset button on the Netgear EAX20 extender.

  2. Use a paperclip or pin to press and hold the Reset button for 10 seconds.

  3. Release the button when the Power LED starts blinking.

  4. Wait for the extender to reboot, which may take a few minutes.

  5. Confirm the extender has reset when the Power LED turns solid.

  6. Reconnect to the extender's default WiFi network (Netgear_ext).

  7. Complete the setup process again if needed.