Crack propagation direction is correlated with pre-set joint angles of the specimens. https://www.selleckchem.com/products/gdc-0077.html With the increase of the pre-set joint angles, the crack initiation angle decreases gradually. When the joint angles are around 30°-75°, the specimens develop obvious cracks. The crushing process of the specimens is simulated by LS-DYNA software. It is concluded that the stresses at the crack initiation time are concentrated between 20 and 40 MPa. The instantaneous stress curve first increases and then decreases with crack propagation, peaking at different times under various joint angles; but most of them occur when the crack penetration ratio reaches 80-90%. With the increment of joint angles in specimens through the simulation software, the changing trend of peak stress is consistent with the test results.In the facilities for the production of Radioactive Ion Beams (RIBs) according to the Isotope Separation On-Line (ISOL) technique, a production target is typically impinged by a high-power primary beam, generating radioactive isotopes for basic research and technological applications. With the aim to guarantee an efficient extraction of the aforementioned isotopes, the production target must work in a high vacuum environment, at temperatures that are usually between 1600 °C and 2200 °C. Its main components are often characterized by intense temperature gradients and consequently by severe thermal stresses. Carbides are widely used for target manufacturing, and in this work a specific method for their thermal and mechanical characterization is presented and discussed. It is based on the comparison between experimental measurements and numerical simulations, with the introduction of the novel Virtual Thermoelastic Parameters approach for the structural verification procedure. High-performance silicon carbides (SiC) are taken as a reference to describe the method. Measured emissivity and thermal conductivity data are presented and discussed, together with the experimental estimation of material limitations for both temperature and stress fields. The aforementioned results can be promptly used for the design process of high-power ISOL targets.Blast furnace ferronickel slag (BFFS) is generated in the production of ferronickel alloys and is used as cement replacement in concrete or mortar. The effectivity in reducing cement consumption and improving performance are limited. By referring to the paste replacement method, this work used BFFS to replace an equal volume of the white Portland cement paste to obtain greater performance enhancement. BFFS was used with five levels of replacement (0%, 5%, 10%, 15%, 20%) and four water-to-cement ratios (0.40, 0.45, 0.50, 0.55) were designed. Fluidity, mechanical strength, hydration products, and pore structure of every mixture were measured. The results showed that the workability of the mortars decreased due to the reduced volume of water, but the 28-day compressive strength of the mortars increased, and the cement content of the mortars was also reduced by 33 wt %. The X-ray diffraction (XRD) patterns revealed that there existed a carboaluminate phase, and the presence of the ettringite was stabilized, indicating that the accumulating amount of the hydration products of the mortar increased. Furthermore, the BFFS could consume the portlandite and free water to form a higher amount of chemically bound water due to its pozzolanic activity. A high degree of hydration and a large volume of the hydration products refined the porosity of the hardened mortars, which explained the enhancement of the strength of the mortars. Compared to the cement replacement method, the paste replacement method was more effective in preparing eco-friendly mortar or concrete by recycling BFFS for reducing the cement content of the mortar while improving its strength.The glycidyl-POSS (Polyhedral Oligomeric Silsesquioxanes, Polysilsesquioxane, POSS) (Gly-POSS) and trisilanolisooctyl-POSS (HO-POSS) were applied as functional additives influencing on the viscoelastic properties of the dynamic vulcanized PLA/ENR (poly(lactic acid)/epoxidized natural rubber) blends. The plasticizing effect of HO-POSS on PLA/ENR melt, leading to the decrease of complex viscosity at 160 °C, was observed. After the incorporation of Gly-POSS into PLA/ENR blends the complex viscosity increased confirming that the epoxy groups of Gly-POSS were able to react with the functional groups of ENR and the groups present at the end of PLA chains. The incorporation of Gly-POSS into 4060 PLA/ENR blend provided significant enhancement of the storage shear modulus G' at 30 °C. Furthermore, the glass transition temperatures Tg of ENR phase for PLA/ENR/Gly-POSS blends were shifted to higher values of temperature as compared with blends modified by HO-POSS. Strong reduction of the elongation at break Eb for 4060 PLA/ENR/Gly-POSS blend indicated that Gly-POSS particles acted as multifunctional cross-links reducing elasticity of the material. The modification of 4060 PLA/ENR blend by HO-POSS molecules led to lower values of composting coefficient KC indicating stronger deterioration of the mechanical properties that resulted from more intense degradation processes occurring during disposal in soil.In recent decades, efforts have been made to achieve a positive coexistence among adolescents in secondary schools and create a healthy environment to prepare them to face the present-day challenges. Therefore, this study highlights the educational purpose of improving emotional management and social skills as well as decreasing antisocial and criminal behaviour among secondary education students through an educational training programme. Accordingly, to verify the effectiveness of the project, a quasi-experimental design with a pre-test/post-test structure and a control group was adopted. To achieve this, a total of 141 Spanish secondary school students participated in this study and were randomly assigned to one of two experimental conditions. The first (experimental) group (n = 55) participated in the training programme; correspondingly, the second group (control) (n = 57) followed the usual mentoring activities planned for the entire educational centre. Of the total number of participants, 52.7% of the sample were men and 47.